This ad is for two MOS through bolt chamfered washers for a case nut of a 3.0 liter Porsche 911 and or Porsche 930. I think this washer was changed from a flat washer 1965 - 1974 and then beginning with engines with a 90 mm bore or larger the chamfer was added to prevent them from interfering with the cylinder fit and holding up the base of the larger diameter cylinders thus causing them to not...
This ad is for a used OEM lower engine lid latch for a 1965 - 1989 Porsche 911 and or a Porsche 930. The latch is in good condition and aside from needing a thorough cleaning it is ready for installation. The Porsche part number for the latch is 901.512.052.00 I am asking $75.00 for the part plus $10.50 in postage and paypal fees
This ad is for a used OEM engine lid grill for a 1970 - 1976 Porsche 914. The grill is in good condition. Basically what you see is what you get. The Porsche part number is I am asking $80.00 for the lid plus $28.50 in postage and paypal fees
This ad is for a used custom engine lid for what is thought to be a 1974 - 1977 Porsche 930 Turbo without the inter cooler. I am not at all sure of this so please do your homework to insure this is correct for your needs. This is a very unusual design and what is not noticeable is that the fiberglass lid itself is bonded to the factory steel sub frame. This is how the factory built the historic...
This ad is for a used OEM engine lid grill with rain tray for a 1970 - 1976 Porsche 914. The grill is in outstanding condition but unfortunately it got scratched and scuffed while in storage. It is missing the Porsche letters. I believe the scuff and scratch can be buffed out with a mild polishing compound. The Porsche part number for the lid is 914.512.022.10 The Porsche part number for the gr...
This ad is for a used OEM rear engine lid assembly with a turbo style rubber spoiler added for a 1974 - 1989 Porsche 911 and or a Porsche 930 Turbo. This engine lid assembly is often called a whale tail and sometimes a "tea tray" it comes stock on a Porsche 930 Turbo and the cars with the M491 wide body kit to make a narrow body car into a Turbo look Porsche 911. This particular engine lid is a...
This ad is for a used OEM engine lid latch assembly with pull cable and knob for a 1970 - 1976 Porsche 914-4 and or a 914-6. This parts are in good condition and aside from a good thorough cleaning they are ready for installation. Lubricate the cable before installing it. The Porsche part number for the latch is 914.512.029.10 The Porsche part number for the lid release cable 914.511.091.10 I a...
This ad is for a new custom engine lid grille for a 1974 - 1989 Porsche 911 / 912E and or a Porsche 930. Although the grill will fit the 1969 - 1973 Porsche 911 and Porsche 912 models as well. This is a lightweight, retro-cool, perforated-metal grille for the 911. The grille is made from sheet aluminum and has been powder coated black. It comes with the hardware and mounting instructions. It is...
This ad is for a used OEM lower engine lid latch for a 1965 - 1989 Porsche 911 and or a Porsche 930 and the 1976 Porsche 912E. The latch is in good condition and aside from needing a thorough cleaning it is ready for installation. The Porsche part number for the latch is 901.512.052.00 I am asking $75.00 for the part plus $10.50 in postage and paypal fees
New IPD Cummins ISX Inframe Overhaul KitP KIF187996Matches with the following piston numbers3684467, 2882631, 4367173, 4376244Or the following CPLs0927, 1434, 2733, 2919, 2965, 3167, 3458, 8660EGR 2007 Non DPF Cummins EngineCall with engine serial number to confirm availability.
I have a 1969 Pontic 350 complete except carb ran when pulled needs rebuilt 9790079 $500 ,Pontiac 1976 400 block crank rods pistons oil pan 500557 $350 ,6x heads $250,1965 389421 67cc closed chamber heads complete orange in pics ,also have a Pontiac 350 turbo$150 and a Pontiac 400 turbo $250 transmissions ,aluminum lt1 heads off 1996 corvette $300 calls only will not answer emails
We are selling a CADILLAC NORTHSTAR DTS ENGINE. It has 156k miles, runs good. Should fit a 2006-2011. I am also selling the transmission. Located in Conway, AR. FOR FASTER RESPONSE, call or text me. 4797472695
This is a service for head bolt thread repair on GM LS engines and other GM engines that have the M11x2.0 thread. If you are reading this, you have a thread that has pulled out while putting a cylinder head back on. The tool you need to do this is very expensive, and we have it. Time-Sert 3700. We had this exact problem and had to purchase the tool to do it, but before we did we called everyone...
CHOATE ENGINEERING PERFORMANCE IS LOCATED IN WHITEVILLE, T.NLong blocks, short blocks, diy kits, or full runners for all powerstroke, cummins and duramax.. just give us a call so we can give you an exact estimate and answer any questions you may have concerning an engine build.visit us at Choates engineering and performance on facebook.
This engine came from a 1982 F150 pickup. The truck sat since 2012. To get it running I replaced the plugs fuel pump. It starts right up and runs very well. No smoke, no knocks and no funny noises. It showed normal oil pressure on the Ford dash gauge. I have no idea how many miles are on the engine or anything about the internal condition. I did notice some oil at the front of the intake block ...
2008 Pontiac G8 GT needs motor. READ 6.0 V8 auto 147k miles Still runs but has 2 bent rods and is has a rattle in it, its rebuild able. Cars not perfect needs front bumper repaired or replaced, driver seat has a tear and rear driver side seat has a tear, and head liner is sagging, fuel door replaced, and a good cleaning. Serious inquires only and Bring a trailer. May part out would rather sell ...
Mopar 383 engine with full drive train. Donor vehicle. Engine not running. Have new starter. 1200 OBO. Car included. Trades welcome.
This ad is for a used OEM rear engine mount cross member with two engines mount support brackets for a 1965 - 1989 Porsche 911. This part is ideal for those wanting to convert a stock 1965 - 1969 Porsche 912 to a 911. The part is in very good condition with no rust to speak of aside from surface rust. The support bracket both look to be in excellent condition as well as the cross member itself....